Parquet pricing is never a single number. It is the sum of five components: the material type and wear layer thickness, the wood species and grading class, the surface finish, the subfloor preparation and labour, and finally the ancillary materials together with transport. To read a square metre cost correctly, you need to ask about each of these five items separately.
The largest share of any price difference comes from what the floor is made of and how much genuine timber sits on the top surface.
Solid parquet is produced from one piece of wood through its entire thickness, which places it at the upper band of square metre cost. Engineered parquet combines a real wood top layer of between 2 and 6 mm with a multi layer carrier body. This construction reduces raw material consumption and at the same time improves dimensional stability, which is why it has become the default choice in many hotel and apartment projects. Laminate and SPC floors create the appearance of timber through a printed decor layer, so they are generally the most economical options on the list.
Wear layer thickness is directly linked to service life. A product with a 0.6 mm peeled veneer and a product with a 4 mm sawn veneer may look identical on the day of installation, but only the second one can be sanded and refinished years later. If you want to compare solid boards with thick veneered products before deciding, the content gathered under solid parquet articles is a sensible starting point.
Two boards of the same thickness can carry very different prices depending on the species used, the cutting method and the selection grade.
Oak sits in the middle of the price scale because its hardness and grain pattern have made it the most widely used species in the sector, which keeps supply steady. Walnut, iroko and teak form the higher band, partly because they are harder to source and partly because of their natural durability. Beech and ash are priced variably according to colour and cut.
The cut itself is decisive. Quarter sawn or radial cut lamellas show straighter grain and behave more predictably in terms of dimensional movement, but the yield from each log is lower, so the cost rises. The grading class, meaning the distinction between knotty, rustic and clean select material, can shift the square metre price significantly on its own. Pattern choice also enters the calculation, because herringbone and Hungarian point layouts require more cutting and longer installation time. For a practical look at how these patterns behave in real rooms, the article Herringbone Laminate Parquet: Elegance and Durability Together offers useful perspective.
How the surface is protected determines both the initial purchase price and the maintenance spending spread across the years.
UV lacquer layers applied in the factory are built up in multiple coats under controlled conditions, so they deliver more uniform protection than lacquering carried out on site after installation. A natural oil or hard wax oil finish produces a matt, tactile surface and allows local repair, which is an advantage over the long term, though it does require periodic re oiling. Brushed, hand scraped or coloured surfaces each represent an additional production step, and that step is reflected in the price.
On the laminate and SPC side, the abrasion class plays the same role. AC3 and AC4 are commonly recommended for residential interiors, while AC5 is the usual specification for busy commercial areas. As the class rises the square metre price rises with it, but so does resistance to scratching and wear. Readers who want to compare the available classes in detail will find extended content under laminate parquet articles.
The most frequently overlooked item in a square metre price, and the one that produces the most surprises, is the condition of the substrate underneath the parquet.
If the screed surface is not level, levelling compound, self smoothing screed or additional preparation labour becomes necessary. The widely accepted practice in the sector is that relative humidity in a cement based screed should fall below roughly 2 percent before installation begins, and the threshold is kept lower for anhydrite screeds. Starting work without taking a moisture reading creates a genuine risk of cupping and delamination, which eventually leads to relaying the floor, the single most expensive outcome of all.
Labour pricing also shifts with the installation method. Click systems are the fastest and most economical approach. Full bonding consumes more adhesive and more craftsman hours. Patterned layouts such as herringbone and Hungarian point take noticeably longer than straight plank installation. Door frame undercuts, returns around columns and cuts around kitchen islands all add measurable man hours. She Parquet treats transparency here as essential and lists these items separately during the site survey rather than hiding them inside a single rate.
The small items that sit outside the headline figure can push the total square metre cost up considerably.
Underlay, moisture barrier film, adhesive, skirting boards, transition profiles, corner trims and end beads are the main members of this group. Underfloor heating installations call for a specialist underlay with low thermal resistance, and these products cost more than standard underlay. It is also generally accepted that the surface temperature over underfloor heating should not exceed 27 degrees, which makes correct board thickness an important part of the specification.
Waste allowance belongs in the budget as well. Planning roughly 5 to 7 percent waste for straight laying, and a higher figure for patterned work, is common practice. Transport, floor access, portering and the time the material spends acclimatising in the room are further items that stretch across the schedule. The scope and duration of the manufacturer warranty can be a legitimate reason for a price gap too. For a look at the product range in this category, the article on imported engineered parquet is worth reviewing.
Comparing two quotations by looking only at the square metre figure usually leads to the wrong decision.
The first mistake is failing to clarify whether the price covers material only or material plus labour. The second is not asking about wear layer thickness, because the difference between 2 mm and 4 mm decides whether the floor can ever be sanded again. The third is leaving finishing details such as skirting boards and profiles out of the quotation, only for them to arrive later as an extra invoice.
The fourth is excluding subfloor preparation from the scope. A figure given before a survey has confirmed whether levelling is required is simply not realistic. The fifth is ignoring lifetime cost. A cheap floor replaced twice in ten years can end up more expensive than a quality product installed once and repaired as needed. The approach She Parquet follows in residential and hotel projects is to discuss traffic intensity and expected service life at the outset, then match the material to those answers rather than to a headline rate.
Pricing is generally calculated per square metre, but a waste allowance is added to the total. Planning roughly 5 to 7 percent for straight laying, and a higher allowance for patterned layouts such as herringbone, is standard practice.
Solid parquet is made from one piece of timber through its full thickness and therefore consumes far more raw material. In engineered boards, genuine wood is used only in a top layer of 2 to 6 mm, while the layers beneath are made from more economical carrier materials.
Labour depends on the installation method, the pattern and the condition of the substrate. Straight click laying is the most economical option, while full bonding and patterns such as herringbone or Hungarian point require more craftsman hours and raise the cost.
Always ask about wear layer thickness, wood species and grading class, abrasion class, whether subfloor preparation is included, and whether skirting boards and transition profiles are part of the price. These five questions make two quotations genuinely comparable.
Yes, because it requires a specialist underlay with low thermal resistance and a dimensionally stable board in a suitable thickness. The generally accepted limit of 27 degrees surface temperature also narrows the material choice, which can be reflected in the price.